Page 1 of 1

VASP 5.2 Installation failure of parallel version

Posted: Sat Jun 27, 2009 3:30 am
by hacret
------------------------------------------
SGE 6.1
Intel ICT 3.1
-Fortran compiler : 10.1.015
-CMKL : 10.0.011
-MPI : 3.1

The parallel version compilation is successful. However,
I got the following errer message when I tried to put the job.

please help me
---------------------------------------------------------------------
running on 16 nodes
distr: one band on 1 nodes, 16 groups
vasp.5.2.2 15Apr09 complex
POSCAR found : 2 types and 36 ions
scaLAPACK will be used
LDA part: xc-table for Pade appr. of Perdew
POSCAR, INCAR and KPOINTS ok, starting setup
FFT: planning ...( 1 )
reading WAVECAR
entering main loop
N E dE d eps ncg rms rms(c)
rank 14 in job 2 compute-0-2_57118 caused collective abort of all ranks
exit status of rank 14: killed by signal 9
rank 10 in job 2 compute-0-2_57118 caused collective abort of all ranks
exit status of rank 10: killed by signal 9
rank 6 in job 2 compute-0-2_57118 caused collective abort of all ranks
exit status of rank 6: killed by signal 9
rank 2 in job 2 compute-0-2_57118 caused collective abort of all ranks
exit status of rank 2: killed by signal 9

---------------------------------------------------------------------

I set the value "NPAR=16"
When I set the NPAR=4 or 8, vasp runnimg is successful even if the runtime is more longer.
Next passage is Makefile.
---------------------------------------------------------------------- .SUFFIXES: .inc .f .f90 .F
#-----------------------------------------------------------------------
# Makefile for Intel Fortran compiler for Pentium/Athlon/Opteron
# bases systems
# we recommend this makefile for both Intel as well as AMD systems
# for AMD based systems appropriate BLAS and fftw libraries are
# however mandatory (whereas they are optional for Intel platforms)
#
# The makefile was tested only under Linux on Intel and AMD platforms
# the following compiler versions have been tested:
# - ifc.7.1 works stable somewhat slow but reliably
# - ifc.8.1 fails to compile the code properly
# - ifc.9.1 recommended (both for 32 and 64 bit)
# - ifc.10.1 partially recommended (both for 32 and 64 bit)
# tested build 20080312 Package ID: l_fc_p_10.1.015
# the gamma only mpi version can not be compiles
# using ifc.10.1
#
# it might be required to change some of library pathes, since
# LINUX installation vary a lot
# Hence check ***ALL*** options in this makefile very carefully
#-----------------------------------------------------------------------
#
# BLAS must be installed on the machine
# there are several options:
# 1) very slow but works:
# retrieve the lapackage from ftp.netlib.org
# and compile the blas routines (BLAS/SRC directory)
# please use g77 or f77 for the compilation. When I tried to
# use pgf77 or pgf90 for BLAS, VASP hang up when calling
# ZHEEV (however this was with lapack 1.1 now I use lapack 2.0)
# 2) more desirable: get an optimized BLAS
#
# the two most reliable packages around are presently:
# 2a) Intels own optimised BLAS (PIII, P4, PD, PC2, Itanium)
# http://developer.intel.com/software/products/mkl/
# this is really excellent, if you use Intel CPU's
#
# 2b) probably fastest SSE2 (4 GFlops on P4, 2.53 GHz, 16 GFlops PD,
# around 30 GFlops on Quad core)
# Kazushige Goto's BLAS
# http://www.cs.utexas.edu/users/kgoto/signup_first.html
# http://www.tacc.utexas.edu/resources/software/
#
#-----------------------------------------------------------------------

# all CPP processed fortran files have the extension .f90
SUFFIX=.f90

#-----------------------------------------------------------------------
# fortran compiler and linker
#-----------------------------------------------------------------------
#FC=ifort
# fortran linker
#FCL=$(FC)


#-----------------------------------------------------------------------
# whereis CPP ?? (I need CPP, can't use gcc with proper options)
# that's the location of gcc for SUSE 5.3
#
# CPP_ = /usr/lib/gcc-lib/i486-linux/2.7.2/cpp -P -C
#
# that's probably the right line for some Red Hat distribution:
#
# CPP_ = /usr/lib/gcc-lib/i386-redhat-linux/2.7.2.3/cpp -P -C
#
# SUSE X.X, maybe some Red Hat distributions:

CPP_ = ./preprocess <$*.F | /usr/bin/cpp -P -C -traditional >$*$(SUFFIX)

#-----------------------------------------------------------------------
# possible options for CPP:
# NGXhalf charge density reduced in X direction
# wNGXhalf gamma point only reduced in X direction
# avoidalloc avoid ALLOCATE if possible
# PGF90 work around some for some PGF90 / IFC bugs
# CACHE_SIZE 1000 for PII,PIII, 5000 for Athlon, 8000-12000 P4, PD
# RPROMU_DGEMV use DGEMV instead of DGEMM in RPRO (depends on used BLAS)
# RACCMU_DGEMV use DGEMV instead of DGEMM in RACC (depends on used BLAS)
#-----------------------------------------------------------------------

#CPP = $(CPP_) -DHOST=\"LinuxIFC\" \
-Dkind8 -DCACHE_SIZE=12000 -DPGF90 -Davoidalloc -DNGXhalf \
-DRPROMU_DGEMV -DRACCMU_DGEMV

#-----------------------------------------------------------------------
# general fortran flags (there must a trailing blank on this line)
# byterecl is strictly required for ifc, since otherwise
# the WAVECAR file becomes huge
#-----------------------------------------------------------------------

FFLAGS = -I/opt/intel/cmkl/10.0.011/include/fftw -FR -lowercase
#FFLAGS = -FR -lowercase -assume byterecl

#-----------------------------------------------------------------------
# optimization
# we have tested whether higher optimisation improves performance
# -axK SSE1 optimization, but also generate code executable on all mach.
# xK improves performance somewhat on XP, and a is required in order
# to run the code on older Athlons as well
# -xW SSE2 optimization
# -axW SSE2 optimization, but also generate code executable on all mach.
# -tpp6 P3 optimization
# -tpp7 P4 optimization
#-----------------------------------------------------------------------

# ifc.9.1, ifc.10.1 recommended
OFLAG=-O3

OFLAG_HIGH = $(OFLAG)
OBJ_HIGH =
OBJ_NOOPT =
DEBUG = -FR -O0
INLINE = $(OFLAG)

#-----------------------------------------------------------------------
# the following lines specify the position of BLAS and LAPACK
# VASP works fastest with the libgoto library
# so that's what we recommend
#-----------------------------------------------------------------------

# mkl.10.0
# set -DRPROMU_DGEMV -DRACCMU_DGEMV in the CPP lines
#BLAS=-L/opt/intel/mkl100/lib/em64t -lmkl -lpthread
MKL_LIB=/opt/intel/cmkl/10.0.011/lib/em64t
BLAS=-L$(MKL_LIB) -lmkl_intel_lp64 -lmkl_sequential -lmkl_core -lpthread
LAPACK=-L$(MKL_LIB) -lmkl_lapack

# even faster for VASP Kazushige Goto's BLAS
# http://www.cs.utexas.edu/users/kgoto/signup_first.html
# parallel goto version requires sometimes -libverbs
#BLAS= /opt/libs/libgoto/libgoto.so

# LAPACK, simplest use vasp.5.lib/lapack_double
#LAPACK= ../vasp.5.lib/lapack_double.o

# use the mkl Intel lapack
#LAPACK= -lmkl_lapack

#-----------------------------------------------------------------------

#LIB = -L../vasp.5.lib -ldmy \
../vasp.5.lib/linpack_double.o $(LAPACK) \
$(BLAS)

# options for linking, nothing is required (usually)
#LINK =

#-----------------------------------------------------------------------
# fft libraries:
# VASP.5.2 can use fftw.3.1.X (http://www.fftw.org)
# since this version is faster on P4 machines, we recommend to use it
#-----------------------------------------------------------------------

#FFT3D = fft3dfurth.o fft3dlib.o
#FFT3D = fftmpiw.o fftmpi_map.o fftw3d.o fft3dlib.o $(MKL_LIB)/libfftw3xf_intel.a
#FFT3D = fftw3d.o fft3dlib.o $(MKL_LIB)/libfftw3xf_intel.a

# alternatively: fftw.3.1.X is slighly faster and should be used if available
#FFT3D = fftw3d.o fft3dlib.o /opt/libs/fftw-3.1.2/lib/libfftw3.a


#=======================================================================
# MPI section, uncomment the following lines until
# general rules and compile lines
# presently we recommend OPENMPI, since it seems to offer better
# performance than lam or mpich
#
# !!! Please do not send me any queries on how to install MPI, I will
# certainly not answer them !!!!
#=======================================================================
#-----------------------------------------------------------------------
# fortran linker for mpi
#-----------------------------------------------------------------------

FC=mpiifort
FCL=$(FC)

#-----------------------------------------------------------------------
# additional options for CPP in parallel version (see also above):
# NGZhalf charge density reduced in Z direction
# wNGZhalf gamma point only reduced in Z direction
# scaLAPACK use scaLAPACK (usually slower on 100 Mbit Net)
#-----------------------------------------------------------------------

CPP = $(CPP_) -DMPI -DHOST=\"LinuxIFC\" -DIFC \
-Dkind8 -DCACHE_SIZE=4000 -DPGF90 -Davoidalloc -DNGZhalf \
-DMPI_BLOCK=8000 -DRPROMU_DGEMV -DRACCMU_DGEMV -DscaLAPACK

#-----------------------------------------------------------------------
# location of SCALAPACK
# if you do not use SCALAPACK simply leave that section commented out
#-----------------------------------------------------------------------

#BLACS=$(HOME)/archives/SCALAPACK/BLACS/
#SCA_=$(HOME)/archives/SCALAPACK/SCALAPACK

#SCA= $(SCA_)/libscalapack.a \
# $(BLACS)/LIB/blacsF77init_MPI-LINUX-0.a $(BLACS)/LIB/blacs_MPI-LINUX-0.a $(BLACS)/LIB/blacsF77init_MPI-LINUX-0.a

SCA=$(MKL_LIB)/libmkl_scalapack_lp64.a $(MKL_LIB)/libmkl_blacs_intelmpi_lp64.a

#-----------------------------------------------------------------------
# libraries for mpi
#-----------------------------------------------------------------------

LIB = -L../vasp.5.lib -ldmy \
../vasp.5.lib/linpack_double.o $(LAPACK) \
$(SCA) $(BLAS)

# FFT: fftmpi.o with fft3dlib of Juergen Furthmueller
#FFT3D = fftmpi.o fftmpi_map.o fft3dfurth.o fft3dlib.o
#FFT3D = fftmpi.o fftmpi_map.o fft3dfurth.o fft3dlib.o $(MKL_LIB)/libfftw3xf_intel.a
FFT3D = fftmpiw.o fftmpi_map.o fftw3d.o fft3dlib.o $(MKL_LIB)/libfftw3xf_intel.a

# alternatively: fftw.3.1.X is slighly faster and should be used if available
#FFT3D = fftmpi.o fftmpi_map.o fftw3d.o fft3dlib.o /opt/libs/fftw-3.1.2/lib/libfftw3.a

#-----------------------------------------------------------------------
# general rules and compile lines
#-----------------------------------------------------------------------
BASIC= symmetry.o symlib.o lattlib.o random.o

SOURCE= base.o mpi.o smart_allocate.o xml.o \
constant.o jacobi.o main_mpi.o scala.o \
asa.o lattice.o poscar.o ini.o xclib.o xclib_grad.o \
radial.o pseudo.o mgrid.o gridq.o ebs.o \
mkpoints.o wave.o wave_mpi.o wave_high.o \
$(BASIC) nonl.o nonlr.o nonl_high.o dfast.o choleski2.o \
mix.o hamil.o xcgrad.o xcspin.o potex1.o potex2.o \
metagga.o constrmag.o cl_shift.o relativistic.o LDApU.o \
paw_base.o egrad.o pawsym.o pawfock.o pawlhf.o paw.o \
mkpoints_full.o charge.o dipol.o pot.o \
dos.o elf.o tet.o tetweight.o hamil_rot.o \
steep.o chain.o dyna.o sphpro.o us.o core_rel.o \
aedens.o wavpre.o wavpre_noio.o broyden.o \
dynbr.o rmm-diis.o reader.o writer.o tutor.o xml_writer.o \
brent.o stufak.o fileio.o opergrid.o stepver.o \
chgloc.o fast_aug.o fock.o mkpoints_change.o sym_grad.o \
mymath.o internals.o dimer_heyden.o dvvtrajectory.o vdwforcefield.o \
hamil_high.o nmr.o force.o \
pead.o subrot.o subrot_scf.o pwlhf.o gw_model.o optreal.o davidson.o \
electron.o rot.o electron_all.o shm.o pardens.o paircorrection.o \
optics.o constr_cell_relax.o stm.o finite_diff.o elpol.o \
hamil_lr.o rmm-diis_lr.o subrot_cluster.o subrot_lr.o \
lr_helper.o hamil_lrf.o elinear_response.o ilinear_response.o \
linear_optics.o linear_response.o \
setlocalpp.o wannier.o electron_OEP.o electron_lhf.o twoelectron4o.o \
ratpol.o screened_2e.o wave_cacher.o chi_base.o wpot.o local_field.o \
ump2.o bse.o acfdt.o chi.o sydmat.o

INC=

vasp: $(SOURCE) $(FFT3D) $(INC) main.o
rm -f vasp
$(FCL) -o vasp main.o $(SOURCE) $(FFT3D) $(LIB) $(LINK)
makeparam: $(SOURCE) $(FFT3D) makeparam.o main.F $(INC)
$(FCL) -o makeparam $(LINK) makeparam.o $(SOURCE) $(FFT3D) $(LIB)
zgemmtest: zgemmtest.o base.o random.o $(INC)
$(FCL) -o zgemmtest $(LINK) zgemmtest.o random.o base.o $(LIB)
dgemmtest: dgemmtest.o base.o random.o $(INC)
$(FCL) -o dgemmtest $(LINK) dgemmtest.o random.o base.o $(LIB)
ffttest: base.o smart_allocate.o mpi.o mgrid.o random.o ffttest.o $(FFT3D) $(INC)
$(FCL) -o ffttest $(LINK) ffttest.o mpi.o mgrid.o random.o smart_allocate.o base.o $(FFT3D) $(LIB)
kpoints: $(SOURCE) $(FFT3D) makekpoints.o main.F $(INC)
$(FCL) -o kpoints $(LINK) makekpoints.o $(SOURCE) $(FFT3D) $(LIB)

clean:
-rm -f *.g *.f *.o *.L *.mod ; touch *.F

main.o: main$(SUFFIX)
$(FC) $(FFLAGS)$(DEBUG) $(INCS) -c main$(SUFFIX)
xcgrad.o: xcgrad$(SUFFIX)
$(FC) $(FFLAGS) $(INLINE) $(INCS) -c xcgrad$(SUFFIX)
xcspin.o: xcspin$(SUFFIX)
$(FC) $(FFLAGS) $(INLINE) $(INCS) -c xcspin$(SUFFIX)

makeparam.o: makeparam$(SUFFIX)
$(FC) $(FFLAGS)$(DEBUG) $(INCS) -c makeparam$(SUFFIX)

makeparam$(SUFFIX): makeparam.F main.F
#
# MIND: I do not have a full dependency list for the include
# and MODULES: here are only the minimal basic dependencies
# if one strucuture is changed then touch_dep must be called
# with the corresponding name of the structure
#
base.o: base.inc base.F
mgrid.o: mgrid.inc mgrid.F
constant.o: constant.inc constant.F
lattice.o: lattice.inc lattice.F
setex.o: setexm.inc setex.F
pseudo.o: pseudo.inc pseudo.F
poscar.o: poscar.inc poscar.F
mkpoints.o: mkpoints.inc mkpoints.F
wave.o: wave.inc wave.F
nonl.o: nonl.inc nonl.F
nonlr.o: nonlr.inc nonlr.F

$(OBJ_HIGH):
$(CPP)
$(FC) $(FFLAGS) $(OFLAG_HIGH) $(INCS) -c $*$(SUFFIX)
$(OBJ_NOOPT):
$(CPP)
$(FC) $(FFLAGS) $(INCS) -c $*$(SUFFIX)

fft3dlib_f77.o: fft3dlib_f77.F
$(CPP)
$(F77) $(FFLAGS_F77) -c $*$(SUFFIX)

.F.o:
$(CPP)
$(FC) $(FFLAGS) $(OFLAG) $(INCS) -c $*$(SUFFIX)
.F$(SUFFIX):
$(CPP)
$(SUFFIX).o:
$(FC) $(FFLAGS) $(OFLAG) $(INCS) -c $*$(SUFFIX)

# special rules
#-----------------------------------------------------------------------
# these special rules are cummulative (that is once failed
# in one compiler version, stays in the list forever)
# -tpp5|6|7 P, PII-PIII, PIV
# -xW use SIMD (does not pay of on PII, since fft3d uses double prec)
# all other options do no affect the code performance since -O1 is used

fft3dlib.o : fft3dlib.F
$(CPP)
$(FC) -FR -lowercase -O2 -c $*$(SUFFIX)
fft3dfurth.o : fft3dfurth.F
$(CPP)
$(FC) -FR -lowercase -O1 -c $*$(SUFFIX)

radial.o : radial.F
$(CPP)
$(FC) -FR -lowercase -O1 -c $*$(SUFFIX)

symlib.o : symlib.F
$(CPP)
$(FC) -FR -lowercase -O1 -c $*$(SUFFIX)

symmetry.o : symmetry.F
$(CPP)
$(FC) -FR -lowercase -O1 -c $*$(SUFFIX)

wave_mpi.o : wave_mpi.F
$(CPP)
$(FC) -FR -lowercase -O1 -c $*$(SUFFIX)

wave.o : wave.F
$(CPP)
$(FC) -FR -lowercase -O1 -c $*$(SUFFIX)

dynbr.o : dynbr.F
$(CPP)
$(FC) -FR -lowercase -O1 -c $*$(SUFFIX)

asa.o : asa.F
$(CPP)
$(FC) -FR -lowercase -O1 -c $*$(SUFFIX)

broyden.o : broyden.F
$(CPP)
$(FC) -FR -lowercase -O2 -c $*$(SUFFIX)

us.o : us.F
$(CPP)
$(FC) -FR -lowercase -O1 -c $*$(SUFFIX)

LDApU.o : LDApU.F
$(CPP)
$(FC) -FR -lowercase -O2 -c $*$(SUFFIX)
---------------------------------------------------------------------

VASP 5.2 Installation failure of parallel version

Posted: Sat Jun 27, 2009 4:32 pm
by pafell
Signal 9 makes me think it's SGE (queueing system). Specially when you said running 4 threads in parallel works without problems.
It could also be some problem with memory (ex. stack size too small).
I'd suggest asking claster administrator(s) about limits (and best for help resolving your issue). It doesn't look like VASP problem to me.

One more interesting thing in your report is that only one node crashed:
compute-0-2_57118 (all 4 threads on this node crashed, while ohters were killed by queueing system after some threads died.). It could be also crash of node, of nodes network link, etc. Anyways it's almost definitely problem with claster.

VASP 5.2 Installation failure of parallel version

Posted: Mon Jun 29, 2009 1:54 am
by hacret
Thank you for your advice~